Tax incl. Tax excl.
Crystic 15PA Vinyl Ester brush Tooling Gel Coat

Crystic 15PA High Performance Vinylester Brush Tooling Gelcoat Green 2606

WGC0015B-1
9 Items
€27.35

By buying this product you can collect up to 2 points. Your cart will total 2 points that can be converted into a voucher of €0.20.

€27.35 Tax incl. €22.60 Tax excl.
Tax included

Crystic Gelcoat 15PA(B) is designed for use in the manufacture of high quality, FRP composite tooling. It is a pre-accelerated brush gelcoat specially formulated from a vinyl ester base resin and is available in a restricted range of colours. The information contained in this leaflet also applies to pigmented versions.

Supply
Color
  • Verde

 Calculate Shipping Cost
Shipping:
0
to Spain via
Estimated delivery: No estimated delivery specified day(s)
Ratings and comments from our customers
( 5.0 / 5) - 1 feedback(s)

Crystic Gelcoat 15PA(B) is designed for use in the manufacture of high quality, FRP composite tooling. It is a pre-accelerated brush gelcoat specially formulated from a vinyl ester base resin and is available in a restricted range of colours. The information contained in this leaflet also applies to pigmented versions.

Crystic Gelcoat 15PA(B) is heat resistant with high impact strength and good resistance to chemical attack. It is extremely resilient and can be polished to a high gloss.

Crystic Gelcoat 15PA(B) is a tooling gelcoat and the application should be controlled at 0.4 - 0.6 mm wet film thickness. As a guide, approximately 500 - 750 gm-2 of gelcoat (depending on pigment) will give the required thickness when evenly applied. If left for prolonged periods, Crystic Gelcoat 15PA(B) will cure to an almost tack-free finish, but this has no adverse effect on the adhesion of the backing laminate.

Crystic Gelcoat 15PA requires only the addition of catalyst to start the curing reaction. The recommended catalyst is Butanox M50 (or other equivalent catalyst like Luperox K1S), which should be added at 2% into the gelcoat. (Please consult our Technical Service Department if other catalysts are to be used). 

Gel time: between 7 and 12 minutes at 25 °C with 2% MEKP catalyst (Catalyst X-8: Luperox K1S or Butanox M50) .

Deflection Temperature under load† (1.80 MPa): 106 °C

Type of supply

Crystic 15PA Green Vinylester Brush Tooling Gelcoat x 1 kg, supplied with 20 g of MEKP catalyst

Crystic 15PA Green Vinylester Brush Tooling Gelcoat x 5 kg, supplied with 100 g of MEKP catalyst

Crystic 15PA Green Vinylester Brush Tooling Gelcoat x 25 kg, supplied with 0.5 kg of MEKP catalyst

9 Items

ADR (DANGEROUS GOODS)

Some products will be considered dangerous goods (ADR) when their container exceed certain amounts. ADR products must be transported by special transport agencies, such as DACHSER or TXT.

* The following products will be considered ADR (Dangerous Goods) when their container EXCEED the values shown in the table below. Products of equal or smaller size than those shown will not be considered ADR, so they may be transported also by SEUR/DPD and GLS.

____________________________________________________

PRODUCT                                                                     

Polyvinyl and Isopropyl alcohol ................................................  1 L

Ethylmethylketone / Methyl ethyl ketone ................................... 1 L

Acetone ....................................................................................   1 L

Methyl ethyl ketone Peroxide (X-8 MEKP Catalyst) ...................125 ml

Liquid Amine or Liquid Polyamide (Epoxy Resin Hardener) ....... 5 L

Resins, Top Coats and Gel Coats ................................................ 5 L

Paints ......................................................................................... 5 L

Styrene and MW Paraffin Solution .............................................. 5 L

_____________________________________________________________

If you have selected a product whose container size is considered ADR and you choose SEUR or Correos EXPRESS as carrier, those ADR products will be transferred into smaller containers to not breach the European Agreement concerning the International Carriage of Dangerous Goods by Road. That is, if you order a 25 kg resin drum and you select SEUR or Correos Express as carrier because you need the products sooner, the resin will be supplied in 5 containers of 5 kg each and its catalyst will be supplied in 5 containers of 100 g.

In any case, drums bigger than 25 kg must be shipped by TXT or Dachser.

* Shippings to Portugal will be always carried by Torrestir

Customers who bought this product also bought:

Ratings and comments from our customers

Score:  
 
 -   (Baños de rio Tobia, Spain)
Gran calidad. Facilita mucho el desmoldeo
Product added to wishlist