Tax incl. Tax excl.
Crystic 65PA Top Coat Black

Crystic Topcoat 65PAX Black 505 Brush Isophthalic Polyester Topcoat

WTC0505-1
7 Items
€23.90

By buying this product you can collect up to 2 points. Your cart will total 2 points that can be converted into a voucher of €0.20.

€23.90 Tax incl. €19.75 Tax excl.
Tax included

Crystic Topcoat 65PAX Black 505 is a pre-accelerated, isophthalic topcoat. It has been formulated for brush application and is available in a restricted range of colours. 

Crystic Topcoat 65PAX Black 505 is designed for use where a smooth finish is required on the reverse side of a laminate.

Supply

 Calculate Shipping Cost
Shipping:
0
to Spain via
Estimated delivery: No estimated delivery specified day(s)
Ratings and comments from our customers
( 5.0 / 5) - 2 feedback(s)

Crystic Topcoat 65PAX Black 505 is a pre-accelerated, isophthalic topcoat. It has been formulated for brush application and is available in a restricted range of colours. 

Crystic Topcoat 65PAX Black 505 is designed for use where a smooth finish is required on the reverse side of a laminate.

Crystic Topcoat 65PAX Black 505 has low styrene emission. It is not air inhibited, and produces a matt finish.

Crystic Topcoat 65PAX Black 505 should be allowed to attain workshop temperature (18 ºC - 20 ºC) before use. Stir well by hand, or with a low shear mixer to avoid aeration, and then allow to stand to regain thixotropy. Crystic Topcoat 65PAX Black 505  requires only the addition of catalyst to start the curing reaction. The recommended catalyst is Butanox M50 (or other equivalent catalyst), which should be added at 2% into the topcoat. (Please consult our Technical Service Department if other catalysts are to be used). The catalyst should be thoroughly incorporated into the topcoat, with a low shear mechanical stirrer where possible. 

Gel time at 20 ºC: 15 minutes

Deflection Temperature Under Load (1.80 MPa): 75 ºC.

Type of supply

Crystic Topcoat 65PAX Black 505 isophthalic polyester topcoat x 1 kg, supplied with 20 g of catalyst MEKP

Crystic Topcoat 65PAX Black 505 isophthalic polyester topcoat x 5 kg, supplied with 100 g of catalyst MEKP

Crystic Topcoat 65PAX Black 505 isophthalic polyester topcoat x 25.75 kg, supplied with 0.5 kg of catalyst MEKP

7 Items

ADR (DANGEROUS GOODS)

Some products will be considered dangerous goods (ADR) when their container exceed certain amounts. ADR products must be transported by special transport agencies, such as DACHSER or TXT.

* The following products will be considered ADR (Dangerous Goods) when their container EXCEED the values shown in the table below. Products of equal or smaller size than those shown will not be considered ADR, so they may be transported also by SEUR/DPD and GLS.

____________________________________________________

PRODUCT                                                                     

Polyvinyl and Isopropyl alcohol ................................................  1 L

Ethylmethylketone / Methyl ethyl ketone ................................... 1 L

Acetone ....................................................................................   1 L

Methyl ethyl ketone Peroxide (X-8 MEKP Catalyst) ...................125 ml

Liquid Amine or Liquid Polyamide (Epoxy Resin Hardener) ....... 5 L

Resins, Top Coats and Gel Coats ................................................ 5 L

Paints ......................................................................................... 5 L

Styrene and MW Paraffin Solution .............................................. 5 L

_____________________________________________________________

If you have selected a product whose container size is considered ADR and you choose SEUR or Correos EXPRESS as carrier, those ADR products will be transferred into smaller containers to not breach the European Agreement concerning the International Carriage of Dangerous Goods by Road. That is, if you order a 25 kg resin drum and you select SEUR or Correos Express as carrier because you need the products sooner, the resin will be supplied in 5 containers of 5 kg each and its catalyst will be supplied in 5 containers of 100 g.

In any case, drums bigger than 25 kg must be shipped by TXT or Dachser.

* Shippings to Portugal will be always carried by Torrestir

    Asked by: Roberto
    Date: 2020-10-26 17:23:26
    Hello, I have bought a bottle of topcoat to be applied with a roller and I have painted some panels of the boat and I would like to give a second coat, where I bought it I asked them and they told me to apply acetone first and to give it another coat, but there have been marks of the roller. With another coat they go away or do I have to carefully pass a 600 sandpaper?

    We recommend sanding before applying a second coat. Ideally, you should do it with a thicker sandpaper, 320-400, so that it generates a good mechanical anchor. Leaving a completely mark-free finish is complex, so once that second coat is dry you will have to sand, polish and polish. At that point you can start with a 600-800 or even 1000, it all depends on how you finished.


    Asked by: Rene Trowe
    Date: 2020-10-26 19:09:38
    I would like to paint my boat with a new gelcoat. He still has his old gelcoat completely. I want to repaint it.

    A gelcoat should not be applied over an old gelcoat as it will peel off over time. Even if you sand the old gelcoat. To apply a gelcoat/topcota, you would need to remove the old gelcoat and then apply a new resin and fiber laminate. Another option  would be to sand the old gelcoat, then apply an epoxy primer and finally 2-3 coats of 100 g/m2 each of a high-resistance polyurethane paint.


Customers who bought this product also bought:

Ratings and comments from our customers

Score:  
 
 -   (Tresserve, France)
No comments
Score:  
 
 -   (EPARGNES, France)
super !
Product added to wishlist