Tax incl. Tax excl.
Topcoat Duratec® Viniléster Alto Brillo Negro 1901-045
Topcoat Duratec® Viniléster Alto Brillo Negro 1901-045
Topcoat Duratec® Viniléster Alto Brillo Negro 1901-045
Topcoat Duratec® Viniléster Alto Brillo Negro 1901-045

Duratec® 707-002 Polyester Duratec Surface Primer Epoxy Compatible

WRPM0007-PCA
0 Item
Out-of-Stock
€229.90

By buying this product you can collect up to 22 points. Your cart will total 22 points that can be converted into a voucher of €2.20.

€229.90 Tax incl. €190.00 Tax excl.
Tax included

The ultimate High-Gloss surface primer for wood, MDF, tooling board and composite plugs, patterns and models. Unique air-cure technology for fast cure even with thin coats. Easy to sand, polish to a gloss. Take a mold directly off the Surface Primer or topcoat for the highest gloss.

ONLY PRODUCED AND SUPPLIED ON DEMAND (lead time: 1-3 weeks)

Supply

 Calculate Shipping Cost
Shipping:
0
to Spain via
Estimated delivery: No estimated delivery specified day(s)
Ratings and comments from our customers
( 0.0 / 5) - 0 feedback(s)

The ultimate High-Gloss surface primer for wood, MDF, tooling board and composite plugs, patterns and models. Unique air-cure technology for fast cure even with thin coats. Easy to sand, polish to a gloss. Take a mold directly off the Surface Primer or topcoat for the highest gloss.

ONLY PRODUCED AND SUPPLIED ON DEMAND (lead time: 1-3 weeks)

Recommended Uses:

• Surface coat for plugs/ patterns for composite tooling.

• Easy Sanding High-Build Primer for composite parts.

• High Build, Fast Sanding Primer perfectly smooth surfaces Recommended Uses: (cont)

• A substitute for sanding gelcoat -epoxy laminates or pinhole-free surfaces.

• Highly crosslinked coating providing excellent chemical resistance

Features:

Low Porosity- provides a super fine leveling and filling system. Applied properly, Surface Primer provides a porosity-free surface without pinholes or defects.

Adhesion to most epoxies- with heat distortion level of 200° F/93 C the primer also adheres to fiberglass, wood, MDF, brick, concrete and polyurethane foam.

Rapid Buildup- up to 40 mils 1000 micorns, wet on wet, on composite plugs and master mold surfaces. Save time and labor.

Easy Sanding-also saves time and labor. The primer cures to a surface that polishes to a gloss.

Product Properties:

Viscosity as measured on a Brookfield Visometer Model RFG, Spindle #5 at 2.5 rpm: 2300-2600 cps

Thixotropic: 5

Gel Time: Sample based upon a 100 g mass, catalyzed with 2% Norox 925: 16-24 min

Weight per Gallon: 10.9 lb, 4.995 kg.

Coverage per Gallon:

10 mil thickness (wet-dry):160 ft2 -125 ft2

250 micron thickness (wet-dry): 15 m2 -12 m2

Use Instructions:

• Mix thoroughly with a drill-mounted mixer or paint shaker. Hand stirring is not enough.

• Duratec Surface Primer is designed to be applied when the ambient temperature and part temperature are both above 60°F.

• Catalyze with 1.75-2.25% MEKP Catalyst. Norox 925 works well. Mix well.

• Surface Primer can be applied by roller, brush or by spray. Spray with an HVLP gun, or with a gelcoat application system. Seek a fine spray, and use the lowest pressure that allows an even spray fan. (approximately 40 psi). A 2.0 mm tip is recommended.

• Apply at least 10 mils for even and complete cure. . Recoat before the Primer has set up and lost its tack. If the Primer cures completely wait at least eight hours, sand, and recoat.

• Additional solvent is not needed for most spray guns. If solvent is required, do not add Acetone or Styrene.

• Duratec Thinner is the best choice. Methyl Ethyl Ketone Solvent will work for most users. High quality urethane reducers are good choices. Lacquer Thinners are not recommended.

• Sand when the primer has cured. Start with the finest paper that will remove the surface profile. If sprayed well, 220 or 320 grit paper is a good starting point.

• Wait at least eight hours from the start of sanding before polishing or topcoating.

• Aqua Buff 1000 and 2000 are good choices for compounding and polishing Surface Primer.

• Duratec Pot Life Extender will extend the pot life by 2-3 times, and does not extend the cure time (spray only).

Type of supply

Duratec® 707-002 Polyester Duratec Surface Primer x 4,99 kg (1 gallon) supplied with 100 g MEKP Catalyst.

Customers who bought this product also bought:

Product added to wishlist