Tax incl. Tax excl.
TensorGrip TC49 - Infusion Moulding HI-TAC Adhesive Fine Mist Spray
TensorGrip TC49 - Infusion Moulding HI-TAC Adhesive Fine Mist Spray
TensorGrip TC49 - Infusion Moulding HI-TAC Adhesive Fine Mist Spray
TensorGrip TC49 - Infusion Moulding HI-TAC Adhesive Fine Mist Spray

TensorGrip TC49 - Infusion Moulding HI-TAC Adhesive Fine Mist Spray

FAMC-TC49
0 Item
Out-of-Stock
€12.95
€15.67 Tax incl. €12.95 Tax excl.
Tax excluded

By buying this product you can collect up to 1 point points. Your cart will total 1 point that can be converted into a voucher of €0.10.

TensorGrip® TC49 is a spray adhesive designed for the infusion mould market. With an immediate tack to hold the reinforcing fibres, you will also achieve a great surface finish with carbon fibre applications thanks to its fine mist spray properties. It is compatible with polyester, styrene and vinyl ester resins and been successfully tested with epoxy resins using less than 9 g of adhesive per m2.

Choose the type of supply

Ratings and comments from our customers
( 0.0 / 5) - 0 feedback(s)

TensorGrip® TC49 is a spray adhesive designed for the infusion mould market. With an immediate tack to hold the reinforcing fibres, you will also achieve a great surface finish with carbon fibre applications thanks to its fine mist spray properties. TensorGrip® TC49 is compatible with polyester, styrene and vinyl ester resins and been successfully tested with epoxy resins using less than 9 grams of adhesive per sqm. The short open time makes TensorGrip® TC49 ideal for small area applications.

ADVANTAGES  

  • Extra Fine Mist Spray
  • Safely Fuses Laminating Materials To Structural Core Surfaces
  • Great Surface Finish Results

DIRECTIONS FOR USE

  • This product is designed to be applied to one side of the surfaces to be bonded together, However, It can be used for double sided bonding where required. Make sure that surfaces are clean, dry and free from dirt, dust, oil, loose paint, wax or grease, etc. For best results, the temperature of the adhesive and the surfaces being bonded should be between 60oF - 80oF (16oC - 27oC).·       When possible we recommend shaking the canister well before using
  • Attach and secure hose tightly onto the spray gun with required tip. Attach the other end of the hose onto the canister. Make sure the hose-valve connections are securely tight. Open the valve on the canister slowly and fully, check for leaks during this process. Unlock the trigger on the spray gun to start spraying.
  • Prior to use, check compatibility by spraying a small test patch of the adhesive on the substrate. This product may degrade some substrates. 
  1. Make sure that surfaces are clean, dry and free from dirt, dust, oil, loose paint, wax or grease, etc.
  2. Spray about 10-20 cm (4” – 8”) away at a 90 degree angle to the surface, applying a uniform, even coat of adhesive to obtain 80% to 100% coverage of the surface. If necessary, spray another coat of adhesive in areas that appear to need more adhesive.
  3. Spray both surfaces to be bonded, one surface vertically and the other surface horizontally.
  4. Allow 2 - 3 minutes for the adhesive to tack off until no adhesive transfers to the knuckle when touched.
  5. Adhere surfaces and press together with adequate pressure. A roller is recommended to apply a uniform pressure to achieve maximum strength. Allow 24 hours for the adhesive to fully cure.
  6. If the spray tip clogs, unscrew the spray tip from the gun and clean with solvent such as lacquer thinner or acetone. Do not use a pin on the spray tip orifice.

CANISTER STORAGE/CHANGE OVER

Turn valve on canister into the off position, spray out remaining adhesive left in the hose, disconnect the spray hose and gun from the canister.

Reconnect the spray hose to a canister of cleaning solvent (sold separately) and spray out until liquid is clear which indicates that the hose and gun is clean. If you choose to leave the hose and spray gun on the canister, leave the valve on the canister open. Do not disconnect the hose/gun from the canister. Close and lock the spray gun.

SPECIAL PRECAUTIONS

For optimum results store canister above 18°C during use, but must always be above 10°C. Allow substrates to acclimatise to normal room temperature (18°C) for 48 hours before bonding. Do not exceed open time of the adhesive. Keep canister off cold concrete floors during use. If adhesive is expelled wet or as ajet, canister is too cold–move to warm environment and allow to thoroughly acclimatise before reusing.

CAUTION

  • Use only in well ventilated areas.
  • Always read Materila Safety Data Sheets prior to use.
  • DO NOT thin or reactivate with solvents.
  • DO NOT incinerate. DO NOT expose to extreme heat over 50°C.
  • Keep away from sources of ignition.
  • Release pressure before disconnecting hose.
  • Test for suitability before use. 

MSDS and Technical Data Sheets MUST be read and understood before use. Information contained in this technical literature is believed to be accurate and offered in good faith for the benefit of the consumer. The company however cannot assume any liability or risk involved in the use of its chemical products since the conditions of use are beyond our control. Statements concerning the possible use of our products are not intended as recommendations to infringe on any patent.

CHEMICAL TECHNICAL DATA / TYPICAL PROPERTIES

  • Viscosity: 20.5 mm2/s
  • Total Solids: 29%
  • Colour: Clear (aerosol 500 ml available here) or Green
  • System Flammability: Flammable adhesive in flammable propellant
  • Shear> 320.89 p.s.i.
  • 90° Peel (6.25 sq.cm)> 29.3 p.s.i.
  • Shear adhesion failure temp. (SAFT) 100gram > 80°C
  • Dry time30 secs dependant on temp & humidity
  • Open time5 -10 mins
  • SHELF LIFE18 months from date of manufacture

STORAGE HANDLING & STORAGE

  • Consult Material Safety Data Sheet prior to use.
  • Do Not store at temperatures over 50°C.
  • Avoid exposure to direct sunlight.Do Not store directly on concrete floor.
  • For optimum performance, store at 18°C during use, but must always be above 10°C.
  • When connected, keep valve open and hose pressurised at all times.
  • Do Not close valve until ready to connect to new cylinder.
  • Release pressure in hose before disconnection.
  • Always test product to determine suitability for your particular application prior to use in production.

Type of Supply

22 liters disposable canister suitable for industrial use only

500 ml Aerosol suitable for industrial and general public use

You might also like

Customers who bought this product also bought:

Product added to wishlist