Tax incl. Tax excl.
ALEXIT® BladeRep® LEP 10 RAL 7035
ALEXIT® BladeRep® LEP 10 RAL 7035
ALEXIT® BladeRep® LEP 10 RAL 7035
ALEXIT® BladeRep® LEP 10 RAL 7035
ALEXIT® BladeRep® LEP 10 RAL 7035
ALEXIT® BladeRep® LEP 10 RAL 7035

ALEXIT® B, ladeRep® LEP 10 RAL 7035, Leading Edge Protection Coating for Wind Blades

WPUBR1075-0.4
0 Item
Out-of-Stock
€72.98

By buying this product you can collect up to 7 points. Your cart will total 7 points that can be converted into a voucher of €0.70.

€72.98 Tax incl. €72.98 Tax excl.

ALEXIT® BladeRep® LEP 10 is specifically designed one-layer coating with excellent abrasion and erosion resistance. This two-component, solvent free polyurethane product has superior elasticity and flexibility for long-term leading edge protection.

Supply

 Calculate Shipping Cost
Shipping:
0
to Spain via
Estimated delivery: No estimated delivery specified day(s)
Ratings and comments from our customers
( 0.0 / 5) - 0 feedback(s)

Introduction

ALEXIT® BladeRep® LEP 10 is specifically designed to protect leading edge areas where a coating with excellent abrasion and erosion resistance is required. This two-component, solvent-free polyurethane product has superior elasticity and flexibility for long-term leading edge protection. No sanding between layers is needed.

Range of application

ALEXIT® BladeRep® LEP 10 is used for extra protection on highly stressed areas like leading edges of wind turbine rotor blades.

Color:

Similar to 7035 light grey. This product dries to a glossy finish.

Coverage

m² / cartridge Square feet / cartridge
Theoretical coverage at 600 µm / 24 mil of mixed material approx. 0,7 7


Substrate pre-treatment

Sand the surface with 120 grit paper prior to applying ALEXIT® BladeRep® LEP 10. The surface must be clean, dry and free from dust, grease, oil and other contaminates. ALEXIT® BladeRep® LEP 10 may be applied over all BladeRep® products and/or any properly prepared surface.

Mixing Mix by volume

1:1 by volume. Must be processed through a static mixer. 

Equipment needed 

- Cartridge
- Option a) Flex hose brush incl. static mixer or Option b) Static mixer a) Flex hose brush incl. static mixer available in sets (see 13. Packaging) b) Static mixer reference: Sulzer MFH 08-32T or similar (not supplied by Mankiewicz)
- Finish brush
- Dispenser: Sulzer Mixpac DP2X 400-01-50-01(pneumatic) or Cox ElectraFlow Dual Ultra 400 MR 1:1 (battery driven) or equivalent with 1:1 mixing ratio

Application

Apply by Flex hose brush and Finish brush.

Application conditions: 15-32 °C (60-95 °F) and 20-70 % relative humidity. The minimum application condition should be 3°C (5.4°F) above dew point.

Application process for Apply 1 layer of ALEXIT® BladeRep® LEP 10 to a wet film brushing: thickness of minimum 600 µm (24 mil) by using the Flex hose brush for applying the material, followed by the Finish brush for proper smoothing and levelling.

The material should be applied with either a flex hose brush or a static mixer and leveled with the finish brush.

Pot life

5 - 10 min at 23 °C (73 °F)

Drying time 

15 °C (60 °F) 23 °C (73 °F) 30 °C (86 °F)
approx. 50% relative humidity 4 h 3 h 2 h

Type of supply

ALEXIT® BladeRep® LEP 10 RAL 7035 x 400 g cartridge + 1 Finish brush + 1 Flex hose brush

You might also like

Product added to wishlist