Tax incl. Tax excl.
Resoltech 8050L/8059 ultra fast epoxi...

Resoltech 8050L/8059 ultra fast epoxi filler

K8050L-400
0 Item
Out-of-Stock
€63.00
€76.23 Tax incl. €63.00 Tax excl.
Tax excluded

By buying this product you can collect up to 7 point points. Your cart will total 7 points that can be converted into a voucher of €0.70.

RESOLTECH 8050L / 8059 is a ultra fast curing and easy sanding filler. It is a premium choice to substitute polyesters filler.

Due to its very fast curing characteristics it is best to use in cartridges and it is particularly suitable for fast repairs of cracks in mould, finishing of small surface defects, caulking between assembly elements...

It is compatible with all substrate as wood, steel, aluminium and composites.

The specially formulated lightweight epoxy filler may be applied in up to 5 mm on a vertical surface and 10 mm on a horizontal surface in one coat and shows minimal shrinkage upon curing unlike polyurethane or polyester based products.

Once hardened, the 8050L / 8059 filler offers a watertight and impact resistant behaviour. Its Shore 70 D hardness will enable to resist well to vibrations.

Choose the type of supply

Ratings and comments from our customers
( 0.0 / 5) - 0 feedback(s)

  • Can be sanded after 30min
  • Density : 0.79
  • CMR components and solvent free
  • Railway, marine, construction application
  • Cartridge for use with a standard 2K 400mL 1:1 handgun

 

INTRODUCTION

RESOLTECH 8050L / 8059 is a ultra fast curing and easy sanding filler. It is a premium choice to substitute polyesters filler.

Due to its very fast curing characteristics it is best to use in cartridges and it is particularly suitable for fast repairs of cracks in mould, finishing of small surface defects, caulking between assembly elements...

It is compatible with all substrate as wood, steel, aluminium and composites.

The specially formulated lightweight epoxy filler may be applied in up to 5 mm on a vertical surface and 10 mm on a horizontal surface in one coat and shows minimal shrinkage upon curing unlike polyurethane or polyester based products.

Once hardened, the 8050L / 8059 filler offers a watertight and impact resistant behaviour. Its Shore 70 D hardness will enable to resist well to vibrations.

The formulation of the 8050L / 8059 will help improve health and safety for the workers and follows the latest EU regulation (CE) n°453/2010 and does not contain any CMR materials and solvent.

When sanded, the surface of this system is smooth enough to be directly overcoated with RESOLCOAT 3010T / 3014T high build epoxy primer and is compatible with all paints & primers.

Mixing ratio by weight and volume: 1/1

APPLICATION   

  • 8050L / 8059 is only available in cartridge two components. It is possible to use a cartridge in several times if there are several static mixer per cartridge (on demand)
  • It is recommended to use products at a temperature close to 18-25°C in order to facilitate the mixing and the application
  • Lower temperatures will increase the viscosity of the mixture and the gel time, but the resin will not crystallize at low temperatures
  • On the contrary, a higher temperature will reduce the viscosity of the mixture as well as the pot life.

Surface preparation :

        As general rule: all substrates must be sanded, cleaned and dried.

  • On previously painted surfaces : clean thoroughly to degrease the surface and sand with 80-100 grade paper or remove all previous coatings if in poor condition and prime the substrate
  • Steel : prime with ANTICO PRIMER A + B in order to offer a good anticorrosion base
  • Aluminum: it is recommended to either follow an etching/passivation process.
  • Wood: Prime stable constructions only, with RESOLCOAT 1010 / 1014
  • GRP: For osmosis treatment, prime the sanded fibre with 1020L / 102xL in order to waterproof the substrate and lightly sand/deglaze before application of filler 8050L / 8059
  • BARE GRP/COMPOSITE: Remove surface wax/mould release agent with degreaser, sand with 80-100 grade paper. Sand between layer of expoy filler 8050L / 8059 with 80-100 grade paper to ensure a good mechanical adhesion.

 

Overcoating:

RESOLTECH 8050L / 8059 may be overcoated with itself. RESOLCOAT 3010T / 3014T can be apply on the filler sanded and cleaned beforehand.

Warning: It is recommanded to do validation tests before industrial application.

Application coverage vs thickness :

Coverage will depend on the thickness needed to profile. The following table indicates the average consumption vs thickness.

Thickness

Consumption

1 mm

0.79 kg/m²

5 mm

3.95 kg/m²

10 mm

7.9 kg/m²

 

Physical Properties:

Mix density at 23 ºC: 0.79 kg/l

Potlife, sanding & overcoating (on thickness of 2 mm)

Potlife

Can be sanded after

Overcoating* (after sanding)

at 10°C

5 min

45 min

1h15

at 23°C

3 min

30 min

45 min

at 30°C

1 min

20 min

30 min

Shore D hardness after:

8050L/8059

25 min at 23°C

65

24h at 23°C

70

Type of supply

Resoltech 8050L/8059 ultra fast epoxi filler x 400 ml cartridge, supplied with 2 static mixers MEL 14-20

Resoltech 8050L/8059 ultra fast epoxi filler x 13 units of 400 ml cartridge box, supplied with 13 static mixers MEL 14-20

Low shrinkage
Yes

You might also like

Customers who bought this product also bought:

Product added to wishlist